CMCC RAX3000M/CMCC RAX3000Me
Specifications§

- Processor
- MediaTek MT7981B, aarch64, 1300 MHz
- Flash memory
- 128 MB NAND
- RAM
Me-model - 512 MB DDR3
- RAM
M-model - 512 MB DDR4
- Ethernet
- 3 × 1G LAN + 1 × 1G WAN
- USB
- 1 × USB 3.0
- Wi-Fi chip
- MediaTek MT7976CN
- Wi-Fi 5 GHz
- AX, 160MHz, 2x2, 2402MB/s, 1024QAM
- Wi-Fi 2.4 GHz
- AX, 40MHz, 2x2, 574MB/s, 256QAM
Build features§
- FunctionalityExcept:
Cloud services
Components - Factory resetWith the Reset button
- WPS buttonConfigured as Wi-Fi
- Mesh buttonYes
- LEDSystem
Internet connected - Mesh compatibilityWith original devices and clones
- Built-in storage70.9 MB, Entware can be installed
- Modem rebootRequires a hardware mod
Caution
FORESEE F35SQA001G memory and the Airoha AN8855 switch are not supported.
Preparing for flashing§
- Find out the model —
MeorMIt is printed on the sticker on the bottom of the router. File names and the installation order depend on it. - Download and unpack the firmware archive In the panel under the device name, pick your system: Windows, macOS or Linux. Starting the installer on macOS and Linux.
- Connect the router to the computer with a cable (Ethernet)
About the flasher programs
Every *_flasher prepares the EEPROM, generates new service data and installs the firmware. When it finishes, the router reboots automatically.
Installing from stock firmware§
Info
For RAX3000Me only. The M model cannot be installed directly from the stock firmware — use the installation from OpenWrt.
- Factory reset Reset the router to factory settings.
- Creating the configuration Run
1_config-creator.exe(Windows only) and enter the serial number from the sticker on the bottom of the router. A configuration filecfg_yeezyio.confappears next to the program. - Uploading the configuration Open the router's web interface at
192.168.10.1and uploadcfg_yeezyio.confas shown in the screenshots below.


- Flashing After the reboot, run
CMCC_RAX3000ME_flasher, choose Stock firmware and click “Install”. Wait until it finishes — the router reboots with the new firmware.
Done!
Router access
- Web interface
- 192.168.1.1
- Wi-Fi password
12345678
Installing from OpenWrt§
RAX3000Me§
- Uploading the image In the OpenWrt web interface, upload
rax3000m-me-openwrt.itbas an update (sysupgrade). - Flashing After the reboot, run
CMCC_RAX3000ME_flasher, choose OpenWrt and click “Install”. Wait until it finishes. - System start The device starts in about 3 minutes.
Done!
Router access
- Web interface
- 192.168.1.1
- Wi-Fi password
12345678
RAX3000M§
Info
The M model cannot be installed directly from the stock firmware: install OpenWrt yourself first, then follow the steps below.
- Install OpenWrt on the router yourself.
- Uploading the image In the OpenWrt web interface, upload
rax3000m-me-openwrt.itbas an update (sysupgrade). - Flashing After the reboot, run
CMCC_RAX3000M_flasher, choose OpenWrt and click “Install”. Wait until it finishes. - System start The device starts in about 3 minutes.
Done!
Router access
- Web interface
- 192.168.1.1
- Wi-Fi password
12345678
Updating the firmware§
To update, use the Athena bootloader or KeenKit.
Since version 5.0.7 the firmware can also be updated through the web interface.
Reverting to stock firmware§
The revert is done from a full backup through the Athena bootloader. The steps are in the instructions for MT7981.
Rebooting the USB modem (USB-Mod)§
Info
The mod is needed to power-cycle the USB modem — more details
Soldering required
Move the resistor marked in the photos.
For RAX3000Me


For RAX3000M

